My Finished Dining Room DIY Air-Dry Clay Flower Chandelier

Here’s how my clay flower chandelier turned out…

As a reminder, I was inspired by two different lights that I found online. The first one was this $1700 chandelier that had leaves instead of flowers. I really liked the shape of this one…

But I wanted to combine the shape of that chandelier with the flowers from this chandelier…

The first thing I had to do was bend the metal rods that came with the sputnik chandelier. So I used my 25-pound kettlebell, and holding one end of each rod with a pliers in my right hand, I grabbed the other end of the rod with my left hand and gently bent it around the kettlebell to form a gentle curve.

This is what they looked like with the curve…

I decided to screw all of the metal rods into the light before I hung the light to make sure I had the shape right. This made installing the light a little more challenging, but it was much easier to screw all of these in without having to stand on a ladder since there are over 130 of them and this process alone took over an hour.

Once I had the shape of the chandelier right, I moved on to making the air-dry clay flowers. I needed a quick and easy way to make 135 flowers that were all the same size. I could have used a scale to weigh the clay to make sure all of them used the same amount of clay, but I found a much easier and faster way to do this. I had this set of oval metal clay cutters that I bought from Michael’s.

So I used the oval that was the third from the smallest…

I rolled clay out between two pencils using my acrylic clay roller…

And then I cut as many ovals out of that clay as I could…

And then I used two ovals per flower. This assured that each flower used the same amount of clay and came out the same size.

To make each flower, I started by rolling the clay into this smooth egg shape.

And then using a small pair of scissors, I cut about 1/3 of the way through the clay cutting it in half.

And then I cut each half in half again leaving me with four sections…

Then I dipped my fingers into water to which I had added some Dawn dishwashing liquid (I find this works better than plain water), and then used my fingers to press each section into a petal shape. Each petal was pretty rough at this point…

Then I used a small palette knife, dipped it in the water, and used it to smooth out each petal on top and around the edges.

It was still a little rough at this point, but I wasn’t worried about that because this clay, once it’s fully dry, sands to a beautiful, smooth finish with 220-grit sandpaper.

For the final touch, I used a tiny amount of clay, rolled it into a ball…

And pressed that into the center of the flower.

As I pressed that into the center of the flower, the pressure also created a bit of a flat bottom on the flower so that it would sit upright on its own. And then I made sure the petals were curved like I wanted them and placed it aside to dry.

The flowers took about 24 hours to fully dry, and then I sanded each one with 220-grit sandpaper to remove any rough areas. Then I painted each one with this Artist’s Loft Iridescent Medium. I didn’t paint them or prime them first. I didn’t add this medium to any paint. I just used this medium all on its own.

And this is what they looked like when they were dry…

Before attaching them to the chandelier, I had to drill a hole in the bottom of each flower. I taped off my drill bit so that I would know how deep to drill each hole without accidentally drilling all the way through the flower.

To attach the flowers to the chandelier, I initially tried hot glue. That was a mess. It dried way too fast for me to get the flower fully on the metal rod before the glue dried, and then part of it squished out and dried and would have been impossible to completely clean off to give a clean finish. It was a mess. So I ended up using this super glue, and it worked perfectly.

It took me about an hour to attach all of the flowers, but here’s the final result.

I’m so excited about how this light turned out. I think I like this one better than my walk-in closet chandelier, and that one took much longer to make!

Mine isn’t quite as fancy as the inspiration chandelier, but mine also cost under $200 for my DIY version as opposed to the $1700 price of the inspiration chandelier.

In all, it took three packages of the air dry clay to make all 135 flowers, but I only used about 1/3 of the third package. So I have some left over that I can use for another project. And there will be another project because I’ve learned that I absolutely love using this medium to create fun projects.